%PDF-
%PDF-
Mini Shell
Mini Shell
/* SPDX-License-Identifier: GPL-2.0 */
/*
* MPC8xx Communication Processor Module.
* Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
*
* This file contains structures and information for the communication
* processor channels. Some CPM control and status is available
* through the MPC8xx internal memory map. See immap.h for details.
* This file only contains what I need for the moment, not the total
* CPM capabilities. I (or someone else) will add definitions as they
* are needed. -- Dan
*
* On the MBX board, EPPC-Bug loads CPM microcode into the first 512
* bytes of the DP RAM and relocates the I2C parameter area to the
* IDMA1 space. The remaining DP RAM is available for buffer descriptors
* or other use.
*/
#ifndef __CPM1__
#define __CPM1__
#include <linux/init.h>
#include <asm/8xx_immap.h>
#include <asm/ptrace.h>
#include <asm/cpm.h>
/* CPM Command register.
*/
#define CPM_CR_RST ((ushort)0x8000)
#define CPM_CR_OPCODE ((ushort)0x0f00)
#define CPM_CR_CHAN ((ushort)0x00f0)
#define CPM_CR_FLG ((ushort)0x0001)
/* Channel numbers.
*/
#define CPM_CR_CH_SCC1 ((ushort)0x0000)
#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
#define CPM_CR_CH_SCC2 ((ushort)0x0004)
#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI / IDMA2 / Timers */
#define CPM_CR_CH_TIMER CPM_CR_CH_SPI
#define CPM_CR_CH_SCC3 ((ushort)0x0008)
#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
#define CPM_CR_CH_SCC4 ((ushort)0x000c)
#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
/* Export the base address of the communication processor registers
* and dual port ram.
*/
extern cpm8xx_t __iomem *cpmp; /* Pointer to comm processor */
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
#define cpm_dpram_phys cpm_muram_dma
extern void cpm_setbrg(uint brg, uint rate);
extern void __init cpm_load_patch(cpm8xx_t *cp);
extern void cpm_reset(void);
/* Parameter RAM offsets.
*/
#define PROFF_SCC1 ((uint)0x0000)
#define PROFF_IIC ((uint)0x0080)
#define PROFF_SCC2 ((uint)0x0100)
#define PROFF_SPI ((uint)0x0180)
#define PROFF_SCC3 ((uint)0x0200)
#define PROFF_SMC1 ((uint)0x0280)
#define PROFF_DSP1 ((uint)0x02c0)
#define PROFF_SCC4 ((uint)0x0300)
#define PROFF_SMC2 ((uint)0x0380)
/* Define enough so I can at least use the serial port as a UART.
* The MBX uses SMC1 as the host serial port.
*/
typedef struct smc_uart {
ushort smc_rbase; /* Rx Buffer descriptor base address */
ushort smc_tbase; /* Tx Buffer descriptor base address */
u_char smc_rfcr; /* Rx function code */
u_char smc_tfcr; /* Tx function code */
ushort smc_mrblr; /* Max receive buffer length */
uint smc_rstate; /* Internal */
uint smc_idp; /* Internal */
ushort smc_rbptr; /* Internal */
ushort smc_ibc; /* Internal */
uint smc_rxtmp; /* Internal */
uint smc_tstate; /* Internal */
uint smc_tdp; /* Internal */
ushort smc_tbptr; /* Internal */
ushort smc_tbc; /* Internal */
uint smc_txtmp; /* Internal */
ushort smc_maxidl; /* Maximum idle characters */
ushort smc_tmpidl; /* Temporary idle counter */
ushort smc_brklen; /* Last received break length */
ushort smc_brkec; /* rcv'd break condition counter */
ushort smc_brkcr; /* xmt break count register */
ushort smc_rmask; /* Temporary bit mask */
char res1[8]; /* Reserved */
ushort smc_rpbase; /* Relocation pointer */
} smc_uart_t;
/* Function code bits.
*/
#define SMC_EB ((u_char)0x10) /* Set big endian byte order */
/* SMC uart mode register.
*/
#define SMCMR_REN ((ushort)0x0001)
#define SMCMR_TEN ((ushort)0x0002)
#define SMCMR_DM ((ushort)0x000c)
#define SMCMR_SM_GCI ((ushort)0x0000)
#define SMCMR_SM_UART ((ushort)0x0020)
#define SMCMR_SM_TRANS ((ushort)0x0030)
#define SMCMR_SM_MASK ((ushort)0x0030)
#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
#define SMCMR_REVD SMCMR_PM_EVEN
#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
#define SMCMR_BS SMCMR_PEN
#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
/* SMC2 as Centronics parallel printer. It is half duplex, in that
* it can only receive or transmit. The parameter ram values for
* each direction are either unique or properly overlap, so we can
* include them in one structure.
*/
typedef struct smc_centronics {
ushort scent_rbase;
ushort scent_tbase;
u_char scent_cfcr;
u_char scent_smask;
ushort scent_mrblr;
uint scent_rstate;
uint scent_r_ptr;
ushort scent_rbptr;
ushort scent_r_cnt;
uint scent_rtemp;
uint scent_tstate;
uint scent_t_ptr;
ushort scent_tbptr;
ushort scent_t_cnt;
uint scent_ttemp;
ushort scent_max_sl;
ushort scent_sl_cnt;
ushort scent_character1;
ushort scent_character2;
ushort scent_character3;
ushort scent_character4;
ushort scent_character5;
ushort scent_character6;
ushort scent_character7;
ushort scent_character8;
ushort scent_rccm;
ushort scent_rccr;
} smc_cent_t;
/* Centronics Status Mask Register.
*/
#define SMC_CENT_F ((u_char)0x08)
#define SMC_CENT_PE ((u_char)0x04)
#define SMC_CENT_S ((u_char)0x02)
/* SMC Event and Mask register.
*/
#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */
#define SMCM_BSY ((unsigned char)0x04)
#define SMCM_TX ((unsigned char)0x02)
#define SMCM_RX ((unsigned char)0x01)
/* Baud rate generators.
*/
#define CPM_BRG_RST ((uint)0x00020000)
#define CPM_BRG_EN ((uint)0x00010000)
#define CPM_BRG_EXTC_INT ((uint)0x00000000)
#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000)
#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000)
#define CPM_BRG_ATB ((uint)0x00002000)
#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
#define CPM_BRG_DIV16 ((uint)0x00000001)
/* SI Clock Route Register
*/
#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000)
#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000)
#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800)
#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100)
#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000)
#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000)
#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000)
#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000)
/* SCCs.
*/
#define SCC_GSMRH_IRP ((uint)0x00040000)
#define SCC_GSMRH_GDE ((uint)0x00010000)
#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
#define SCC_GSMRH_REVD ((uint)0x00002000)
#define SCC_GSMRH_TRX ((uint)0x00001000)
#define SCC_GSMRH_TTX ((uint)0x00000800)
#define SCC_GSMRH_CDP ((uint)0x00000400)
#define SCC_GSMRH_CTSP ((uint)0x00000200)
#define SCC_GSMRH_CDS ((uint)0x00000100)
#define SCC_GSMRH_CTSS ((uint)0x00000080)
#define SCC_GSMRH_TFL ((uint)0x00000040)
#define SCC_GSMRH_RFW ((uint)0x00000020)
#define SCC_GSMRH_TXSY ((uint)0x00000010)
#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
#define SCC_GSMRH_RTSM ((uint)0x00000002)
#define SCC_GSMRH_RSYN ((uint)0x00000001)
#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
#define SCC_GSMRL_TCI ((uint)0x10000000)
#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
#define SCC_GSMRL_RINV ((uint)0x02000000)
#define SCC_GSMRL_TINV ((uint)0x01000000)
#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
#define SCC_GSMRL_TEND ((uint)0x00040000)
#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
#define SCC_GSMRL_ENR ((uint)0x00000020)
#define SCC_GSMRL_ENT ((uint)0x00000010)
#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
#define SCC_GSMRL_MODE_QMC ((uint)0x0000000a)
#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
#define SCC_TODR_TOD ((ushort)0x8000)
/* SCC Event and Mask register.
*/
#define SCCM_TXE ((unsigned char)0x10)
#define SCCM_BSY ((unsigned char)0x04)
#define SCCM_TX ((unsigned char)0x02)
#define SCCM_RX ((unsigned char)0x01)
typedef struct scc_param {
ushort scc_rbase; /* Rx Buffer descriptor base address */
ushort scc_tbase; /* Tx Buffer descriptor base address */
u_char scc_rfcr; /* Rx function code */
u_char scc_tfcr; /* Tx function code */
ushort scc_mrblr; /* Max receive buffer length */
uint scc_rstate; /* Internal */
uint scc_idp; /* Internal */
ushort scc_rbptr; /* Internal */
ushort scc_ibc; /* Internal */
uint scc_rxtmp; /* Internal */
uint scc_tstate; /* Internal */
uint scc_tdp; /* Internal */
ushort scc_tbptr; /* Internal */
ushort scc_tbc; /* Internal */
uint scc_txtmp; /* Internal */
uint scc_rcrc; /* Internal */
uint scc_tcrc; /* Internal */
} sccp_t;
/* Function code bits.
*/
#define SCC_EB ((u_char)0x10) /* Set big endian byte order */
/* CPM Ethernet through SCCx.
*/
typedef struct scc_enet {
sccp_t sen_genscc;
uint sen_cpres; /* Preset CRC */
uint sen_cmask; /* Constant mask for CRC */
uint sen_crcec; /* CRC Error counter */
uint sen_alec; /* alignment error counter */
uint sen_disfc; /* discard frame counter */
ushort sen_pads; /* Tx short frame pad character */
ushort sen_retlim; /* Retry limit threshold */
ushort sen_retcnt; /* Retry limit counter */
ushort sen_maxflr; /* maximum frame length register */
ushort sen_minflr; /* minimum frame length register */
ushort sen_maxd1; /* maximum DMA1 length */
ushort sen_maxd2; /* maximum DMA2 length */
ushort sen_maxd; /* Rx max DMA */
ushort sen_dmacnt; /* Rx DMA counter */
ushort sen_maxb; /* Max BD byte count */
ushort sen_gaddr1; /* Group address filter */
ushort sen_gaddr2;
ushort sen_gaddr3;
ushort sen_gaddr4;
uint sen_tbuf0data0; /* Save area 0 - current frame */
uint sen_tbuf0data1; /* Save area 1 - current frame */
uint sen_tbuf0rba; /* Internal */
uint sen_tbuf0crc; /* Internal */
ushort sen_tbuf0bcnt; /* Internal */
ushort sen_paddrh; /* physical address (MSB) */
ushort sen_paddrm;
ushort sen_paddrl; /* physical address (LSB) */
ushort sen_pper; /* persistence */
ushort sen_rfbdptr; /* Rx first BD pointer */
ushort sen_tfbdptr; /* Tx first BD pointer */
ushort sen_tlbdptr; /* Tx last BD pointer */
uint sen_tbuf1data0; /* Save area 0 - current frame */
uint sen_tbuf1data1; /* Save area 1 - current frame */
uint sen_tbuf1rba; /* Internal */
uint sen_tbuf1crc; /* Internal */
ushort sen_tbuf1bcnt; /* Internal */
ushort sen_txlen; /* Tx Frame length counter */
ushort sen_iaddr1; /* Individual address filter */
ushort sen_iaddr2;
ushort sen_iaddr3;
ushort sen_iaddr4;
ushort sen_boffcnt; /* Backoff counter */
/* NOTE: Some versions of the manual have the following items
* incorrectly documented. Below is the proper order.
*/
ushort sen_taddrh; /* temp address (MSB) */
ushort sen_taddrm;
ushort sen_taddrl; /* temp address (LSB) */
} scc_enet_t;
/* SCC Event register as used by Ethernet.
*/
#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
/* SCC Mode Register (PMSR) as used by Ethernet.
*/
#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
/* SCC as UART
*/
typedef struct scc_uart {
sccp_t scc_genscc;
char res1[8]; /* Reserved */
ushort scc_maxidl; /* Maximum idle chars */
ushort scc_idlc; /* temp idle counter */
ushort scc_brkcr; /* Break count register */
ushort scc_parec; /* receive parity error counter */
ushort scc_frmec; /* receive framing error counter */
ushort scc_nosec; /* receive noise counter */
ushort scc_brkec; /* receive break condition counter */
ushort scc_brkln; /* last received break length */
ushort scc_uaddr1; /* UART address character 1 */
ushort scc_uaddr2; /* UART address character 2 */
ushort scc_rtemp; /* Temp storage */
ushort scc_toseq; /* Transmit out of sequence char */
ushort scc_char1; /* control character 1 */
ushort scc_char2; /* control character 2 */
ushort scc_char3; /* control character 3 */
ushort scc_char4; /* control character 4 */
ushort scc_char5; /* control character 5 */
ushort scc_char6; /* control character 6 */
ushort scc_char7; /* control character 7 */
ushort scc_char8; /* control character 8 */
ushort scc_rccm; /* receive control character mask */
ushort scc_rccr; /* receive control character register */
ushort scc_rlbc; /* receive last break character */
} scc_uart_t;
/* SCC Event and Mask registers when it is used as a UART.
*/
#define UART_SCCM_GLR ((ushort)0x1000)
#define UART_SCCM_GLT ((ushort)0x0800)
#define UART_SCCM_AB ((ushort)0x0200)
#define UART_SCCM_IDL ((ushort)0x0100)
#define UART_SCCM_GRA ((ushort)0x0080)
#define UART_SCCM_BRKE ((ushort)0x0040)
#define UART_SCCM_BRKS ((ushort)0x0020)
#define UART_SCCM_CCR ((ushort)0x0008)
#define UART_SCCM_BSY ((ushort)0x0004)
#define UART_SCCM_TX ((ushort)0x0002)
#define UART_SCCM_RX ((ushort)0x0001)
/* The SCC PMSR when used as a UART.
*/
#define SCU_PSMR_FLC ((ushort)0x8000)
#define SCU_PSMR_SL ((ushort)0x4000)
#define SCU_PSMR_CL ((ushort)0x3000)
#define SCU_PSMR_UM ((ushort)0x0c00)
#define SCU_PSMR_FRZ ((ushort)0x0200)
#define SCU_PSMR_RZS ((ushort)0x0100)
#define SCU_PSMR_SYN ((ushort)0x0080)
#define SCU_PSMR_DRT ((ushort)0x0040)
#define SCU_PSMR_PEN ((ushort)0x0010)
#define SCU_PSMR_RPM ((ushort)0x000c)
#define SCU_PSMR_REVP ((ushort)0x0008)
#define SCU_PSMR_TPM ((ushort)0x0003)
#define SCU_PSMR_TEVP ((ushort)0x0002)
/* CPM Transparent mode SCC.
*/
typedef struct scc_trans {
sccp_t st_genscc;
uint st_cpres; /* Preset CRC */
uint st_cmask; /* Constant mask for CRC */
} scc_trans_t;
/* IIC parameter RAM.
*/
typedef struct iic {
ushort iic_rbase; /* Rx Buffer descriptor base address */
ushort iic_tbase; /* Tx Buffer descriptor base address */
u_char iic_rfcr; /* Rx function code */
u_char iic_tfcr; /* Tx function code */
ushort iic_mrblr; /* Max receive buffer length */
uint iic_rstate; /* Internal */
uint iic_rdp; /* Internal */
ushort iic_rbptr; /* Internal */
ushort iic_rbc; /* Internal */
uint iic_rxtmp; /* Internal */
uint iic_tstate; /* Internal */
uint iic_tdp; /* Internal */
ushort iic_tbptr; /* Internal */
ushort iic_tbc; /* Internal */
uint iic_txtmp; /* Internal */
char res1[4]; /* Reserved */
ushort iic_rpbase; /* Relocation pointer */
char res2[2]; /* Reserved */
} iic_t;
/*
* RISC Controller Configuration Register definitons
*/
#define RCCR_TIME 0x8000 /* RISC Timer Enable */
#define RCCR_TIMEP(t) (((t) & 0x3F)<<8) /* RISC Timer Period */
#define RCCR_TIME_MASK 0x00FF /* not RISC Timer related bits */
/* RISC Timer Parameter RAM offset */
#define PROFF_RTMR ((uint)0x01B0)
typedef struct risc_timer_pram {
unsigned short tm_base; /* RISC Timer Table Base Address */
unsigned short tm_ptr; /* RISC Timer Table Pointer (internal) */
unsigned short r_tmr; /* RISC Timer Mode Register */
unsigned short r_tmv; /* RISC Timer Valid Register */
unsigned long tm_cmd; /* RISC Timer Command Register */
unsigned long tm_cnt; /* RISC Timer Internal Count */
} rt_pram_t;
/* Bits in RISC Timer Command Register */
#define TM_CMD_VALID 0x80000000 /* Valid - Enables the timer */
#define TM_CMD_RESTART 0x40000000 /* Restart - for automatic restart */
#define TM_CMD_PWM 0x20000000 /* Run in Pulse Width Modulation Mode */
#define TM_CMD_NUM(n) (((n)&0xF)<<16) /* Timer Number */
#define TM_CMD_PERIOD(p) ((p)&0xFFFF) /* Timer Period */
/* CPM interrupts. There are nearly 32 interrupts generated by CPM
* channels or devices. All of these are presented to the PPC core
* as a single interrupt. The CPM interrupt handler dispatches its
* own handlers, in a similar fashion to the PPC core handler. We
* use the table as defined in the manuals (i.e. no special high
* priority and SCC1 == SCCa, etc...).
*/
#define CPMVEC_NR 32
#define CPMVEC_PIO_PC15 ((ushort)0x1f)
#define CPMVEC_SCC1 ((ushort)0x1e)
#define CPMVEC_SCC2 ((ushort)0x1d)
#define CPMVEC_SCC3 ((ushort)0x1c)
#define CPMVEC_SCC4 ((ushort)0x1b)
#define CPMVEC_PIO_PC14 ((ushort)0x1a)
#define CPMVEC_TIMER1 ((ushort)0x19)
#define CPMVEC_PIO_PC13 ((ushort)0x18)
#define CPMVEC_PIO_PC12 ((ushort)0x17)
#define CPMVEC_SDMA_CB_ERR ((ushort)0x16)
#define CPMVEC_IDMA1 ((ushort)0x15)
#define CPMVEC_IDMA2 ((ushort)0x14)
#define CPMVEC_TIMER2 ((ushort)0x12)
#define CPMVEC_RISCTIMER ((ushort)0x11)
#define CPMVEC_I2C ((ushort)0x10)
#define CPMVEC_PIO_PC11 ((ushort)0x0f)
#define CPMVEC_PIO_PC10 ((ushort)0x0e)
#define CPMVEC_TIMER3 ((ushort)0x0c)
#define CPMVEC_PIO_PC9 ((ushort)0x0b)
#define CPMVEC_PIO_PC8 ((ushort)0x0a)
#define CPMVEC_PIO_PC7 ((ushort)0x09)
#define CPMVEC_TIMER4 ((ushort)0x07)
#define CPMVEC_PIO_PC6 ((ushort)0x06)
#define CPMVEC_SPI ((ushort)0x05)
#define CPMVEC_SMC1 ((ushort)0x04)
#define CPMVEC_SMC2 ((ushort)0x03)
#define CPMVEC_PIO_PC5 ((ushort)0x02)
#define CPMVEC_PIO_PC4 ((ushort)0x01)
#define CPMVEC_ERROR ((ushort)0x00)
/* CPM interrupt configuration vector.
*/
#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */
#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrupt */
#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
#define CICR_IEN ((uint)0x00000080) /* Int. enable */
#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
#define CPM_PIN_INPUT 0
#define CPM_PIN_OUTPUT 1
#define CPM_PIN_PRIMARY 0
#define CPM_PIN_SECONDARY 2
#define CPM_PIN_GPIO 4
#define CPM_PIN_OPENDRAIN 8
#define CPM_PIN_FALLEDGE 16
#define CPM_PIN_ANYEDGE 0
enum cpm_port {
CPM_PORTA,
CPM_PORTB,
CPM_PORTC,
CPM_PORTD,
CPM_PORTE,
};
void cpm1_set_pin(enum cpm_port port, int pin, int flags);
enum cpm_clk_dir {
CPM_CLK_RX,
CPM_CLK_TX,
CPM_CLK_RTX
};
enum cpm_clk_target {
CPM_CLK_SCC1,
CPM_CLK_SCC2,
CPM_CLK_SCC3,
CPM_CLK_SCC4,
CPM_CLK_SMC1,
CPM_CLK_SMC2,
};
enum cpm_clk {
CPM_BRG1, /* Baud Rate Generator 1 */
CPM_BRG2, /* Baud Rate Generator 2 */
CPM_BRG3, /* Baud Rate Generator 3 */
CPM_BRG4, /* Baud Rate Generator 4 */
CPM_CLK1, /* Clock 1 */
CPM_CLK2, /* Clock 2 */
CPM_CLK3, /* Clock 3 */
CPM_CLK4, /* Clock 4 */
CPM_CLK5, /* Clock 5 */
CPM_CLK6, /* Clock 6 */
CPM_CLK7, /* Clock 7 */
CPM_CLK8, /* Clock 8 */
};
int cpm1_clk_setup(enum cpm_clk_target target, int clock, int mode);
int cpm1_gpiochip_add16(struct device *dev);
int cpm1_gpiochip_add32(struct device *dev);
#endif /* __CPM1__ */
Zerion Mini Shell 1.0