Current File : //proc/self/root/usr/src/linux-headers-5.15.0-43-generic/include/linux/lis3lv02d.h
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef __LIS3LV02D_H_
#define __LIS3LV02D_H_
/**
* struct lis3lv02d_platform_data - lis3 chip family platform data
* @click_flags: Click detection unit configuration
* @click_thresh_x: Click detection unit x axis threshold
* @click_thresh_y: Click detection unit y axis threshold
* @click_thresh_z: Click detection unit z axis threshold
* @click_time_limit: Click detection unit time parameter
* @click_latency: Click detection unit latency parameter
* @click_window: Click detection unit window parameter
* @irq_cfg: On chip irq source and type configuration (click /
* data available / wake up, open drain, polarity)
* @irq_flags1: Additional irq triggering flags for irq channel 0
* @irq_flags2: Additional irq triggering flags for irq channel 1
* @duration1: Wake up unit 1 duration parameter
* @duration2: Wake up unit 2 duration parameter
* @wakeup_flags: Wake up unit 1 flags
* @wakeup_thresh: Wake up unit 1 threshold value
* @wakeup_flags2: Wake up unit 2 flags
* @wakeup_thresh2: Wake up unit 2 threshold value
* @hipass_ctrl: High pass filter control (enable / disable, cut off
* frequency)
* @axis_x: Sensor orientation remapping for x-axis
* @axis_y: Sensor orientation remapping for y-axis
* @axis_z: Sensor orientation remapping for z-axis
* @driver_features: Enable bits for different features. Disabled by default
* @default_rate: Default sampling rate. 0 means reset default
* @setup_resources: Interrupt line setup call back function
* @release_resources: Interrupt line release call back function
* @st_min_limits[3]: Selftest acceptance minimum values
* @st_max_limits[3]: Selftest acceptance maximum values
* @irq2: Irq line 2 number
*
* Platform data is used to setup the sensor chip. Meaning of the different
* chip features can be found from the data sheet. It is publicly available
* at www.st.com web pages. Currently the platform data is used
* only for the 8 bit device. The 8 bit device has two wake up / free fall
* detection units and click detection unit. There are plenty of ways to
* configure the chip which makes is quite hard to explain deeper meaning of
* the fields here. Behaviour of the detection blocks varies heavily depending
* on the configuration. For example, interrupt detection block can use high
* pass filtered data which makes it react to the changes in the acceleration.
* Irq_flags can be used to enable interrupt detection on the both edges.
* With proper chip configuration this produces interrupt when some trigger
* starts and when it goes away.
*/
struct lis3lv02d_platform_data {
/* please note: the 'click' feature is only supported for
* LIS[32]02DL variants of the chip and will be ignored for
* others */
#define LIS3_CLICK_SINGLE_X (1 << 0)
#define LIS3_CLICK_DOUBLE_X (1 << 1)
#define LIS3_CLICK_SINGLE_Y (1 << 2)
#define LIS3_CLICK_DOUBLE_Y (1 << 3)
#define LIS3_CLICK_SINGLE_Z (1 << 4)
#define LIS3_CLICK_DOUBLE_Z (1 << 5)
unsigned char click_flags;
unsigned char click_thresh_x;
unsigned char click_thresh_y;
unsigned char click_thresh_z;
unsigned char click_time_limit;
unsigned char click_latency;
unsigned char click_window;
#define LIS3_IRQ1_DISABLE (0 << 0)
#define LIS3_IRQ1_FF_WU_1 (1 << 0)
#define LIS3_IRQ1_FF_WU_2 (2 << 0)
#define LIS3_IRQ1_FF_WU_12 (3 << 0)
#define LIS3_IRQ1_DATA_READY (4 << 0)
#define LIS3_IRQ1_CLICK (7 << 0)
#define LIS3_IRQ1_MASK (7 << 0)
#define LIS3_IRQ2_DISABLE (0 << 3)
#define LIS3_IRQ2_FF_WU_1 (1 << 3)
#define LIS3_IRQ2_FF_WU_2 (2 << 3)
#define LIS3_IRQ2_FF_WU_12 (3 << 3)
#define LIS3_IRQ2_DATA_READY (4 << 3)
#define LIS3_IRQ2_CLICK (7 << 3)
#define LIS3_IRQ2_MASK (7 << 3)
#define LIS3_IRQ_OPEN_DRAIN (1 << 6)
#define LIS3_IRQ_ACTIVE_LOW (1 << 7)
unsigned char irq_cfg;
unsigned char irq_flags1; /* Additional irq edge / level flags */
unsigned char irq_flags2; /* Additional irq edge / level flags */
unsigned char duration1;
unsigned char duration2;
#define LIS3_WAKEUP_X_LO (1 << 0)
#define LIS3_WAKEUP_X_HI (1 << 1)
#define LIS3_WAKEUP_Y_LO (1 << 2)
#define LIS3_WAKEUP_Y_HI (1 << 3)
#define LIS3_WAKEUP_Z_LO (1 << 4)
#define LIS3_WAKEUP_Z_HI (1 << 5)
unsigned char wakeup_flags;
unsigned char wakeup_thresh;
unsigned char wakeup_flags2;
unsigned char wakeup_thresh2;
#define LIS3_HIPASS_CUTFF_8HZ 0
#define LIS3_HIPASS_CUTFF_4HZ 1
#define LIS3_HIPASS_CUTFF_2HZ 2
#define LIS3_HIPASS_CUTFF_1HZ 3
#define LIS3_HIPASS1_DISABLE (1 << 2)
#define LIS3_HIPASS2_DISABLE (1 << 3)
unsigned char hipass_ctrl;
#define LIS3_NO_MAP 0
#define LIS3_DEV_X 1
#define LIS3_DEV_Y 2
#define LIS3_DEV_Z 3
#define LIS3_INV_DEV_X -1
#define LIS3_INV_DEV_Y -2
#define LIS3_INV_DEV_Z -3
s8 axis_x;
s8 axis_y;
s8 axis_z;
#define LIS3_USE_BLOCK_READ 0x02
u16 driver_features;
int default_rate;
int (*setup_resources)(void);
int (*release_resources)(void);
/* Limits for selftest are specified in chip data sheet */
s16 st_min_limits[3]; /* min pass limit x, y, z */
s16 st_max_limits[3]; /* max pass limit x, y, z */
int irq2;
};
#endif /* __LIS3LV02D_H_ */
Mini Shell